Get Electron Number

The Get Electron Number building block finds and extracts a number from an Electron application (or from within a specific Electron element) and returns it as an output you can use elsewhere in the flow.

Fully expanded, the et Electron Number block shows the following properties:

Note: The screenshot on this page uses the Elegance Design , introduced in 2025.3. If you are using an earlier version, your layout may look different.

Quick-start

1. Drag Get Electron Number onto the canvas.
2. Connect the block in the flow and specify the basic parameters required for this block to operate: Select Electron Element to get number. Optionally, you can adjust other parameters if needed.
3. Run the flow when it's ready.

Building block parameters

Parameters

• Block header : The green input connector triggers the block to begin execution. The green output connector triggers when an Electron number is successfully fetched. You can rename the block by double-clicking the header text and typing in a new title.

• Select Electron Element to get number : Contains the locator for the Electron element from which the number is extracted. You can capture it by right-clicking and selecting Capture new Electron number , and clear it by right-clicking and selecting Clear Electron number .

• Number found : Contains the number that was found. This output can be connected and used in other building blocks.

• Not found : Triggers if the Electron element is not found before the timeout. This is typically used to branch the execution flow or to explicitly fail a case by linking it to a Fail block.

• Position found : The application canvas position where the element was found in X, Y coordinates (top-left of the application canvas is 0, 0 ).

• Area found : The position and size of the found element in X, Y, Width, Height coordinates, starting with the upper-leftmost pixel.

• Source element : Lets you limit the locator to only search inside a specific source element by selecting the Element option, so the locator applies within that source element rather than the whole window.

• Electron window : Contains a handle to the Electron window once it is found and focus is set. You can pass this to other Electron building blocks to direct them to a specific window when multiple windows are open.

• Find format : Defines a format the number must match to be retrieved. For example, with Price: [NUMBER] USD, only numbers inside text like Price: 123.00 USD are retrieved.

• Is case sensitive : Controls whether Find format is case sensitive. By default, it is case-insensitive.

• 1000 separator : Defines the character used to separate thousands. By default, this uses Leapwork's Windows regional settings (typically "," or ".").

• Decimal separator : Defines the character used to separate decimals. By default, this uses Leapwork's Windows regional settings (typically "," or ".").

• Filter : Defines a filter the number must meet to be retrieved (for example, only retrieve numbers that are Greater than 100 ).

• Use occurrence : Selects which occurrence of the Electron element to use when more than one match is found. Select All to iterate through all occurrences.

• Count : Contains the total number of found occurrences that match the configured locator and criteria.

• Default timeout : If the checkbox is not selected, the timeout is 10 seconds unless changed manually. If the checkbox is selected, the flow's Default timeout under Max. run time applies.

• Timeout (sec) : The maximum time spent searching before giving up and triggering Not found .

• Scroll to find : When set to a value other than None , the block uses scrolling while searching for the Electron element.

• Max repeats : The maximum number of times to perform a scroll before giving up searching for the Electron element.

• Amount : The amount of scrolling that will be performed on each scroll repeat.

• Delay (sec) : The delay in seconds between each of the scroll amounts.

• Scroll into view : When selected, any found Electron element is automatically scrolled into view.

• Await DOM change : Delays the search until there have been no changes to the application's DOM for a specified period (for example, three seconds). Regardless of this checkbox, the search proceeds after waiting a maximum of 30 seconds .

• Await Requests : Delays the search until there have been no active XHR requests for a specified period (for example, three seconds). Regardless of this checkbox, the search proceeds after waiting a maximum of 30 seconds.

Resources